Virus C Output 2 and 3 problem

[dries]

Yes, i'm still on a C.

I got a problem using the output 2 and 3. I want to split the audio signal from the different parts into 3 (or just 2) audio groups.

When I use the system/multi edit menu to route the individual parts to a different output (f.e. part 1-3 to output 1, 4-6 to output 2, and part 7-12 to output 3) this does not work; all the parts are still routed to output 1 :-(

I checked the hardware by defining a second output with the edit menu.
I can use output 2 and 3 - that works (so there is no hardware faillure or cable defect).

But the second output is no help, because with this function all parts are routed to this output.

Am I doing something wrong, or do I have a problem with my synth.

Running on 6.5

Thanks for your help.

[ben crosland]

Yes, i'm still on a C.

I got a problem using the output 2 and 3. I want to split the audio signal from the different parts into 3 (or just 2) audio groups.

When I use the system/multi edit menu to route the individual parts to a different output (f.e. part 1-3 to output 1, 4-6 to output 2, and part 7-12 to output 3) this does not work; all the parts are still routed to output 1 :-(


Am I doing something wrong, or do I have a problem with my synth.

Almost certainly nothing wrong with your Virus.

First of all, try a reset to see if that helps. (Power On whilst holding down LFO Shape - continue to hold until 'Initialising..' messages start appearing).

Another possibility is simply that you are hearing the output of the Delay/Reverb from the other parts out of Out1 - this is because these effects are only ever sent to the main outs.

[dries]

hello ben, thanks for your help.

a reset does not help.

funny thing is, this function should be very simple - I just set the output of a part from Out1 L+R to Out2 L+R or Out3 L+R - I route the output to my mixer and on the 3 stereo channels I should get the different sounds isnt it?

the second output function indeed does work. I can sent the effects to output 2 or 3 and I can sent the normal signal to 2 or 3 (then use balance to mix them together - this works fine). but as I said, that is no help because with this function all parts are routed to the same second output (thats not what I want - I want 3 groups of different parts routed to 3 different outputs).

any ideas??

Thanks.

Dries

[ben crosland]

hello ben, thanks for your help.

a reset does not help.

funny thing is, this function should be very simple - I just set the output of a part from Out1 L+R to Out2 L+R or Out3 L+R - I route the output to my mixer and on the 3 stereo channels I should get the different sounds isnt it?

That does indeed sound correct. I haven't got my Virus C at home right now, so I can't check it out for you today, but if you pm me an arrangement dump of your multi setup, I can take a look at it sometime soon for you.

[dries]

thanks ben, a PM with the midi file has been send to you.

best regards

dries

[tmjorud]

Hello,

I know this is an old post, but I've got the exact same problem, audio from part 2 is routed to OUT 1, no matter what. It seems like I can route part 1 to the other OUTS with no problem, but not with the other parts. Anyone know why it behaves this way? I'm in multisingle mode.

Indigo 2 (virus c) owner.

[Antosub]

Hi there,

it seems like it's quite an old thing but I've got exactly the same trouble right now! :confused:

I've searched in the manual several times but nothing about that.

Could someone help me please?